文档介绍:课程设计任务书
题目: 高频功率放大器设计
初始条件:
1、可选元件:晶体管、高频磁环、电阻、电容、开关等
2、仿真软件:Mulitisim
要求完成的主要任务:
设计一个高频功率放大器,要求
输出功率Po≥125mW
工作中心频率fo=6MHz
>65%
时间安排:
,老师布置课程设计题目,学生根据选题开始查找资料;
。
(1)确定技术方案、电路,并进行分析计算, 时间1天;
(2)选择元器件、安装与调试,或仿真设计与分析,时间2天;
(3)总结结果,写出课程设计报告,时间2天。
指导教师签名: 2010年月日
系主任(或责任教师)签名: 年月日
目录
摘要 II
ABSTRACT II
1 谐振功率放大器的工作原理 3
基本原理电路 3
高频谐振功率放大器的电路组成 3
4
7
谐振功率放大器的动态特性 7
谐振功率放大器的负载特性 7
放大器工作状态的调整 9
2 具体设计过程 10
11
11
11
12
谐振功率放大器的功率和效率关系协调 12
3高频谐振功率放大器电路仿真及结果分析 13
13
13
14
14
15
总结 16
参考文献 17
附录 18
摘要
通信电路中,为了弥补信号在无线传输过程中的衰耗要求发射机具有较大的功率输出,通信距离越远,要求输出功率越大。为获得足够大的高频输出功率,必须采用高频功率放大器。我们对高频功率放大器和低频功率放大器的共同要求是输出功率大和效率高,但由于两者的工作频率和相对带宽相差颇大,就决定了他们之间有根本的差异。基于两种放大器的不同特点,使得这两种功率放大器所选的状态有所不同:低频功放工作于甲类、甲乙类或乙类(限于推挽电路)状态,现在也出现了一些工作于丁类的低频放大器;高频功率放大器则一般工作于丙类(某些特殊情况可工作于甲类、乙类、丁类、戊类等)。
高频放大器的主要技术指标是输出功率、效率、功率增益、带宽和谐波抑制等。这几项指标往往是相互矛盾的,在设计功率放大器时,总是根据该放大器的工作特点,突出其中一些指标,然后兼顾另外一些指标。
Abstract
munication circuits, in order pensate for signal transmission in the wireless transmitter in the attenuation requirements have greater power output, communication, the greater the distance the greater the required output power. In order to obtain a large enough high-frequency output power, high-frequency power amplifier must be used. Our high-frequency power amplifier and low-frequency power amplifier output power of mon requirement is large and high efficiency, but because of the work of both frequency and relative bandwidth vary considerably, we decided there is a fundamental difference between them. Based on two different characteristics of the amplifier, making the status of these two different from the selected power amplifier: low-frequency power amplifier works in Category A, and B or Class B (limited to push-pull circuit) state, an