1 / 70
文档名称:

GPS宽带低噪声放大器及小型化阵列天线研究.pdf

格式:pdf   页数:70
下载后只包含 1 个 PDF 格式的文档,没有任何的图纸或源代码,查看文件列表

如果您已付费下载过本站文档,您可以点这里二次下载

分享

预览

GPS宽带低噪声放大器及小型化阵列天线研究.pdf

上传人:qujim2013 2013/9/7 文件大小:0 KB

下载得到文件列表

GPS宽带低噪声放大器及小型化阵列天线研究.pdf

文档介绍

文档介绍:西安电子科技大学
硕士学位论文
GPS宽带低噪声放大器及小型化阵列天线研究
姓名:石超
申请学位级别:硕士
专业:电磁场与微波技术
指导教师:孙保华
20100101
摘要 I
摘要
微波低噪声放大器是现代通信、雷达、电子战系统中的重要部件。它在很大
程度上对无线接收机的灵敏度,稳定性等性能起着决定性作用。因此,低噪声放
大器的研究是十分有意义的。同时随着现代无线通讯技术的发展,无线通信设备
对天线设计提出了更高的要求。对于小型化阵列天线而言,随着单元天线间的距
离减小,单元天线间的互耦影响加强。小型化阵列天线的去耦问题是一个值得关
注的问题。本文的主要工作有:
本文在综述介绍了低噪声放大器的发展,低噪声放大器的技术指标和宽带低
噪声放大器的设计方法基础上,采用两级拓扑结构,设计出负反馈放大器。该放
大器工作频率在 -,选用噪声系数较低的 Agilent 的 ATF-54143 晶体
管。通过运用 Agilent 公司的微波软件 ADS2008 进行偏置电路、负反馈电路及输
入匹配、级间匹配和输出匹配电路的设计、仿真和优化。实现了在频带内噪声系
数小于 ,小信号增益大于 31dB,增益平坦度为 ,输入驻波比小于 ,
输出驻波比小于 。该放大器制作在 55×52mm2 聚四氟乙烯基板上,经测试满足
设计指标要求。
研究一种新型小型化阵列天线及其去耦网络的分析与设计。提出两单元小型
化阵列天线的结构形式,单元天线采用一种小型化平面印刷单极子天线,阵元间
距2mm,馈电中心间距44mm,。借助电磁仿真软件HFSS设计了
两单元小型化阵列天线的结构参数,分析了单元天线间的隔离度并获得单元天线
的输入阻抗。在此基础上,借助电路仿真软件ADS2008设计了去耦电路和匹配电
路。仿真结果表明,使用去耦网络,两单元小型化阵列天线的端口间隔离度达到
了26dB,:1。

关键词:宽带低噪放负反馈放大器小型化阵列天线去耦网络阻抗匹配
Abstract III
Abstract
Microwave low noise amplifier is an important part of the receiver system of
munication, radar, electron rivalry. It plays key roles in the sensitivity and
stability of wireless receiver preferences. Therefore, the research of low noise amplifier
is of great importance to improve the sensitivity of the receiver. Recent technological
advances in munications have changed the expectations of antenna
designs and their performance. It is very difficult to integrate multiple antennas closely
in a small pact mobile handset while maintaining good isolation between
antenna elements since the antennas couple strongly to each other.
In this paper, we are concerned with the development of low noise amplifier,
technique standard of broadband low noise amplifier and its design at first. For research
of broadband low noise amplifier we choose negative feedback amplifier whose
operating frequency is -. Using the chip of Agilent ATF-54143, we use
two-stage circuits of topology structure. By using Agilent ADS2008, bias a