文档介绍:编号:
毕业设计(论文)说明书
题目: 多路红外遥控发射与接收
电路的设计
院(系):
专业: 电子信息工程
学生姓名:
学号:
指导教师单位:
姓名:
职称:
题目类型: 理论研究实验研究√工程设计工程技术研究软件开发
2012年 5 月 17 日
摘要
随着大规模集成电路和计算机技术的发展,遥控技术才得到快速的发展。在遥控方式上大体经历了从有线到无线的超声波、从振动子到红外线、再到使用总线的微机红外遥控这样几个阶段。无论采用何种方式,准确无误传输信号,最终达到满意的控制效果是非常重要的。最初的无线遥控装置采用的是电磁波传输信号,由于电磁波容易产生干扰,也易受干扰,因此逐渐采用超声波和红外线媒介来传输信号。与红外线相比,超声传感器频带窄,所能携带的信息量少,易受干扰而引起误动作。较为理想的是光控方式,逐渐采用红外线的遥控方式取代了超声波遥控方式,出现了红外线多功能遥控器,成为当今时代的主流。 
红外线遥控装置具有体积小、功耗低、功能强、成本低等特点,因而,继彩电、录像机之后,在录音机、音响设备、空凋机以及玩具等其它小型电器装置上也纷纷采用红外线遥控。工业设备中,在高压、辐射、有毒气体、粉尘等环境下,采用红外线遥控不仅完全可靠而且能有效地隔离电气干扰。
本毕业设计研究的内容是学****和掌握AT89S51单片机的应用技术,红外遥控多路系统的设计,红外遥控的原理以及系统的的实现方法。使电路适合在一定范围内的控制电路,能达到的距离越远越好,可以增加驱动电路的电流驱动能力,且发射管和接收管可以对接收到的红外线信号进行一定的聚焦,尽量使接收功率提高。同时利用单片机对红外信号进行编码、译码、以及脉冲调制,并且用单片机的定时器将信号进行调试。
关键词:单片机;红外遥控;编码;译码;脉冲调制
Abstract
With the large scale integrated circuit puter technology, remote control technology was rapid development. The way the remote control in general has gone from wired to wireless, ultrasound, from the vibrator to the IR, puter and then to use the infrared remote control so the bus several stages. Regardless of the method, accurate signal transmission, and ultimately a good control effect is very important. The first wireless remote control device uses a ic transmission signal, as prone to ic interference, is also susceptible to interference, so the gradual introduction of medium to transmit ultrasonic and infrared signals. Compared with infrared, narrow-band ultrasonic sensor, can carry information less susceptible to interference caused by malfunction. Is the ideal way to light control, and gradually to replace the remote control using infrared remote control ultrasonic method, there have been multi-function infrared remote control, e the mainstream of the times.
Infrared remote control device with small size, low power consumption, powerful, low cost, and thus, following the color TV, VCR, after the tape recorders, audio equipment, air withered machines and toys and other small electrical d