文档介绍：毕业设计(论文) ┊┊┊┊┊┊┊┊┊┊┊┊┊装┊┊┊┊┊订┊┊┊┊┊线┊┊┊┊┊┊┊┊┊┊┊┊长安大学二○一四届毕业论文高速公路设计学院:公路学院专业:道路桥梁与渡河工程(公路工程) 姓名: 学号: 指导教师: 老师完成时间: 2014 年6月二〇一四年六月摘要本论文主要介绍了南宁至柳州高速公路的设计过程。根据给定的设计资料, 通过对现有原始毕业设计(论文) ┊┊┊┊┊┊┊┊┊┊┊┊┊装┊┊┊┊┊订┊┊┊┊┊线┊┊┊┊┊┊┊┊┊┊┊┊数据进行分析, 结合沿线的地质地貌、水文气候等自然条件, 依据《公路工程技术标准》、《公路路线设计规范》等相关规范, 在老师的指导下完成了本次设计任务。本路段所经地区是丘陵区, 依据交通量将路线设计成设计速度为 100 Km/h 的双向四车道高速公路, 路线全长约 51 00米, 路基宽度为 26米。路线设计内容包括平面设计、纵断面设计和横断面设计; 其次进行了排水设计, 采用边沟、排水沟和截水沟等设施进行排水, 保证路基路面的稳定性; 分别进行了沥青路面结构的组合设计和水凝混凝土路面结构的组合设计等内容; 最后对所选最优方案进行施工组织设计和概预算计算。整个设计计算了路线的平、纵曲线要素, 设计了路基、路面、隧道和涵洞等内容, 圆满完成了南宁至柳州高速公路综合设计。关键词: 路线设计,路面设计,排水设计,施工组织与概预算毕业设计(论文) ┊┊┊┊┊┊┊┊┊┊┊┊┊装┊┊┊┊┊订┊┊┊┊┊线┊┊┊┊┊┊┊┊┊┊┊┊ ABSTRACT This paper mainly introduces the design process ofa section ofN anning toL iuzhou highway. Based on the information given by the analysis of the raw data , and the section of geology , topography , terrain , hydrology and other natural conditions , according to "Highway Engineering Technical Standard" , "Road Design Standards" issued by the Ministry munications and other related technologies indicators ,I have finished this task under the teacher's guidance. The area that this highway passes through belongs to plain with plain and hilly area. According to the traffic volume in the future ,I design this highway into design speed of 100Km/h with bi-directional four-lane arterial highway , with route length meters , Subgrade width of26 meters ,3 horizontal curves , and 5 vertical curves. Line design including graphic design , longitudinal design and cross-sectional design; Then I plished the pavement drainage design , which uses ditches and drains for drainage to ensure the water stability of roadbed and pavement; at last ,posite design of pavement structure and other designs are also finished. The whole design have calculated the planar and vertical curve elements of this line , besides roadbed , pavement , bridges and soon. Complete prehensive design of the section of Nanning to Liuzhou arterial highway essfully . KEY WORDS: r