文档介绍:: .
公路桥现浇连续箱梁施工技术-建筑论文
公路桥现浇连续箱梁施工技术
李陆明1,李孟军2
( 河南郑州450003 ;
2. 河南省水利第一工程局 河南郑州450003 )〖HJ*1/2〗
【摘要】盆窑南公路桥是南水北调渠道上的一座桥梁,其上部箱梁采用跨径
(35+54+35)m的现浇连续箱梁,一次性浇筑难度大。本文详细介绍了该桥 梁的支架设计、搭设、预压,模板制安,钢筋制安,混凝土浇筑,预应力张拉 以及支架拆卸等全过程施工技术,可供类似工程施工参考。
关键词 公路桥;现浇连续箱梁;支架;模板;浇筑;张拉
The road bridge cast-in-place continuous box girder construction
tech nique
Li Lu-ming1 , Li Meng-jun2
( conservancy scienee research institute of henan province
Zhe ngzhou He nan 450003 ;
nan province water con serva ncy first Zhen gzhou Henan
450003 )
【Abstract 】Bas in kil n south highway bridge is a bridge on the south-n orth water diversi on cha nn els , the upper box girder used ( 35 + + 35) 54 m span cast-in-place continuous box girder, one-time
casting is difficult. This paper introduces in detail the bridge bracket design, build , preloading , the template system , system of steel bar , concrete pouring , the prestressed tensioning and stent removal , etc. The whole process of the con structi on tech no logy , to provide a refere nee for the similar engin eeri ng con struct ion.
【Key words 】Highway Bridges ; Cast-in-place continuous box
girder ; Support ; The template ; Casting ; The tensile
1. 工程简况
盆窑南公路桥是306省道跨越南水北调渠道的一座桥梁,设计桥梁荷载等级
为公路—I级。该桥全长130m,分3跨,上部采用跨径(35+54+35 )m现 浇连续箱梁。下部结构型式为柱式桥台、钻孔灌注桩基础;柱式桥墩、钻孔灌 注桩基础。连续箱梁采用支架法整体现浇施工。
2. 支架设计
。
由于支架基础要承受整个箱梁重力、模板与支架重力及施工荷载,支架地基
需进行碾压加固后用20cm厚的C20素混凝土进行硬化处理。
。
根据施工图纸计算荷载的最不利情况(梁肋处)如下:
混凝土截面积:
S=*- ( **2m ) + ( 1m*+* )
*2=
混凝土重量:(取钢筋混凝土的重量 R= )
G 砼= X 1mX =
单位面积的重量: q= - = t/m3
T/m2
Q=++= T/m2
。
WDJ碗扣式多功能脚手架作为梁支撑架,
受力验算如下:
以上述计算确定单位面积上最不利垂直均布荷载 T/m2。
(1 )脚手架单元尺寸为 x x ,,顺桥向为
,,最不利处单杆承重 T/m2 x x = 。
(