文档介绍:螺纹紧固件
2
0
2
0
Points 画图要点:
⑴ The contact surface of two parts is represented
双头螺柱 用于联接一通孔薄件和一盲孔厚件。
在图片上点击鼠标左键可以“暂停”或再次“播放”
Screw 螺 钉
Screws are mostly used for the cases with small bearing forces. such as inspection covers which have to be removed frequently.
螺钉 多用于用于受力不大需要经常拆卸的情况。
在图片上点击鼠标左键可以“暂停”或再次“播放”
Nut 螺 母
Nut are used to match the other screw fasteners.
螺母 与其他螺纹件配合使用。
在图片上点击鼠标左键可以“暂停”或再次“播放”
Washer 垫 圈
弹簧垫圈 平垫圈
Washer are used to match the other screw fasteners.
垫圈 与其他螺纹件配合使用。
在图片上点击鼠标左键可以“暂停”或再次“播放”
Assemble views of fasteners 螺栓联接装配图
Using looking-up
table method
按实际尺寸和形状画出
Using the proportional
drawing method
按比例关系完整画出
Simple descriptions
按比例关系简化画出
Assemble views of fasteners 双头螺柱联接装配图
Using looking-up
table method
按实际尺寸和形状画出
Using the proportional
drawing method
按比例关系完整画出
Simple descriptions
按比例关系简化画出
Assemble views of fasteners 螺钉联接装配图
Using the proportional drawing method按比例关系完整画出
Simple
descriptions
按比例关系
简化画出
Using looking-up
table method
按实际尺寸
和形状画出
Assemble views of the set screw
紧定螺钉联接装配图
Assemble views of the set screw 紧定螺钉联接装配图
Before assembly 装配前各零件
The set screw
紧定螺钉
紧定螺钉起防止防止齿轮沿轴向窜动的定位作用
Assemble views of lock washers 止动垫圈联接装配图
Lock washers外舌止动垫圈
Assemble views of lock washers
止动垫圈联接装配图
Lock washers圆螺母止动垫圈装配前各零件
止动垫圈起防止圆螺母松脱的定位作用
Holes of stud and screw
螺栓和螺钉通孔(GB/T 5277-1985)
请点击鼠标左键显示后面内容
Thread specification
In close
In medium
Free fit
Through holes
02
03
03
60°
P
R
R
R
0
01
P’
P’
R
R
R
P’’
P’’
60°
Hexagon nut 六角螺母的画法
,求与中心线的交点01后再画圆弧,求与中心线的交点P和二圆弧的二个交点P’ 。
’为圆心,以圆心至上表面距离为半径画圆弧,既为倒角圆弧。
°斜线的倒角。
,使其宽等于对边距(倒角圆直径),分别以上表面中心和二边为圆心以倒角圆半径画圆弧,求出三圆弧的二交点P’’。
’’’’至上表面的距离为半径 画倒角圆的圆弧既可,再按此法画另一面的圆弧。
注意:侧视图二边是直角。
AF==24×=36
D
AF=
Steps 画图步骤: