文档介绍：辽宁工程技术大学
课程设计
题目:副变速拨叉零件的机械加工工艺规程及加工操纵槽内侧面的工艺装备设计
班级:
姓名:
指导教师:
完成日期:
一、设计题目
副变速拨叉零件的机械加工工艺规程及加工操纵槽内侧面的工艺装备设计
二、原始资料
(1) 被加工零件的零件图 1张
(2) 生产类型:中批或大批大量生产
三、上交材料
(1) 被加工工件的零件图 1张
(2) 毛坯图 1张
(3) 机械加工工艺过程综合卡片(参附表1) 1张
(4) 与所设计夹具对应那道工序的工序卡片 1张
(4) 夹具装配图 1张
(5) 夹具体零件图 1张
(6) 课程设计说明书(5000~8000字) 1份
四、指导教师评语
谢谢朋友对我文章的赏识,充值后就可以下载说明书。我这里还有一个压缩包,里面有相应的word说明书和CAD图纸及CAXA制图。需要压缩包的朋友请联系QQ客服:1459919609。下载后我可以将压缩包免费送给你。需要其他设计题目直接联系!!!
成绩:
指导教师
日期
摘要
本次设计是车床变速箱中拔叉零件的加工工艺规程及一些工序的专用夹具设计。此拔叉零件的结构较为复杂,其加工的地方主要是孔和平面。本设计先加工孔后加工面。将孔与平面的加工明确划分成粗加工和精加工阶段以保证它们的加工精度。基准选择以拔叉右面的最大的平面作为粗基准,来加工中间的通孔,然后以此加工过的孔作为精基准。主要加工工序安排是先以中心孔定位加工出顶平面和右侧平面以及下面的大孔的两平面,再以中心孔定位加工出下端的大孔。加工时是用镗床镗孔。最后以这两个孔为基准,分别加工右侧的槽和顶面的螺纹底孔。整个加工过程选用了钻床、铣床和镗床。工件在机床上定位夹紧选用专用夹具,夹紧方式为手动夹紧,夹紧可靠,操作方便。因此生产效率较高,适用于大批量、流水线上加工。能够满足设计要求。
关键词加工工艺,定位,夹紧,专用夹具
Abstract
This design is a lather to e soon an appropriation for inside pulling out fork spare parts processing craft rules distance and some work prefaces tongs pull out the construction of the fork spare parts than plicacy, its the place that process is a peaceful in bore design processes after processing first the with flat surface the clear and definite dividing the line the bore the coarseness processes to process with the nicety the stage to guarantee their process the precise basis choice to pull out rough basis of conduct and actions of the biggest flat surface of the right in fork, process the in the center in general use bore, then be used as the precise basis with the bore that primarily work preface arrangement is first to process a flat surface with the center bore fixed position with the right side flat surface and below big bore of two flat surface, again with center bore the fixed position processes the big bore that carry processing is to use the boring machine boring these two bores as the basis finally, process the right-hand slot respectively w