文档介绍：爱立信系统第一部分:常用指令及其解释1、RLDEP:CELL=****;打印小区相关数据包括CGI、BSIC、BCCHNO、AGBLK、MFRMS、FNOFFSET、XRANGE、BCCHTYPE等参数常用RLDEC:CELL=****;HNO,H:rlstc:cell=d5357c,state=halted;先halted要修改的小区rldec:cell=d5357c,bcchno=524;rlstc:cell=d5357c,state=active;rlmfc:cell=D5346A,hno=524,mrnic; rlmfc:cell=D5336B,hno=524,mrnic; D5346A、D5336B、5346A……rlmfc:cell=5346B,hno=524,mrnic; 与d5357c有切换关系,rlmfc:cell=5346A,hno=524,mrnic; hno修改后rlmfc:cell=5336C,hno=524,mrnic; 要添加测量频点rlmfc:cell=5336B,hno=524,mrnic; rlmfc:cell=5336A,hno=524,mrnic; rlmfc:cell=D5357B,hno=524,mrnic; rlmfc:cell=D5357A,hno=524,mrnic; rlmfc:cell=5357C,hno=524,mrnic; rlmfc:cell=5357B,hno=524,mrnic; rlmfc:cell=5357A,hno=524,mrnic;修改BSIC:rlstc:cell=d5357c,state=halted;rldec:cell=d5357c,bsic=52;rlstc:cell=d5357c,state=active;:CELL=****,CELLR=****/ALL;查邻区参数,CELL:本小区CELLR:相邻小区rlnri:cell=****,cellr=****;添加相邻关系rlnri:cell=****,cellr=****,single;添加单向相邻关系相邻小区分为三种::添加同MSC同BSC的相邻小区:rlnri:cell=cell1,cellr=cell2;添加cell1到cell2双向相邻关系rlmfc:cell=cell1,hno=**,mrnic;在cell1上添加cell2的测量频点rlmfc:cell=cell2,hno=**,mrnic;在cell2上添加cell1的测量频点rlnri:cell=cell1,cellr=cell2,single;添加cell1到cell2单向相邻关系rlmfc:cell=cell1,hno=**,mrnic;B:添加同MSC不同BSC的相邻小区:要定BSC1CELL1为BSC2CELL2的相邻小区:先定CELL1为BSC2的外部小区:RLDEI:CELL=CELL1,EXT;RLDEC:定义CGI、BCCHNO、BSIC等参数;RLCPC:只定义MSTXPWR,一般为33;RLLOC:定义LOCATINGDATA,EXTPEN为ON;!LOCATINGDATA要与BSC2的参数一致!RLNRI:CELL=CELL2,CELLR=CELL1,SINGLE;RLMFC:CELL=CELL2,HNO=**,MRNIC;如果CELL1已经是BSC2的外部小区:RLNRI:CELL=CELL2,CELLR=CELL1,SINGLE;RLMFC:CELL=CELL2,HNO=**,MRNIC;C:添加不同MSC局间相邻小区:要定MSC1BSC1CELL1为MSC2BSC2CELL2的相邻小区:先在MSC2上定义MSC1的相邻小区MGOCI:CELL=CELL1,MSC=MSC1,CGI=CELL1的CGI;存在,可省去在BSC2上定义CELL1为外部小区RLDEI:CELL=CELL1,EXT;RLDEC:定义CGI、BCCHNO、BSIC等参数;RLCPC:只定义MSTXPWR,一般为33;RLLOC:定义LOCATINGDATA,EXTPEN为ON;!LOCATINGDATA要与BSC2的参数一致!存在,可省去RLNRI:CELL=CELL2,CELLR=CELL1,SINGLE;RLMFC:CELL=CELL2,HNO=**,MRNIC;3、RLHPP:CELL=****;查看chap值CHAP=0为缺省值,CHAP=H用RLHPC:CELL=****,CHAP=*;:CELL=****;查看小区配置的频点、H数目修改TCH:RLCFI:CELL=****,DCHNO=*