文档介绍:ANSYS实验分析报告
姓名:
聂文明
学号:
2013200304
专业:
机械工程
班级:
研13-5班
ANSYS实验分析报告
(聂文明 机械工程 研13-5班)
实验名称:瞬态动力学分析----钟摆摆动分析
一 •问题描述
如图1-0所示为一钟摆装置,初始位置位于%处,求钟摆的位移吋间变化关系。 几何参数:摆杆长度=5m;摆杆横截面积S=6x10-5m2;初始位置00=°0 材料参数:摆锤的质量m=2kg;弹性模量E=200GPa;泊松比Pxy=0. 2;载荷g=9. 8m/s2。
图1-0钟摆结构示意图
二•问题分析
该问题属于瞬态动力学分析问题,,将重力加速度施加在摆锤 上;之后分4个时间段分析摆锤从A运动到B的过程。
三•实验内容
定义工作文件名和工作标题
文件名定义为filel,工作标题定义为zhongbai□
定义单元类型
1)定义两种单元类型:A: Structral Link, spar 8
B: Structral Mass, 3D mass 210 如图IT, 1-2所示。
save db| resum db| Qunl POW
A Element Types
ANSYS Main Menu
同 Preferences
□ Preprocessor
□ Element
@ Switch Elem Type
□ Add DOF
5 Remove DOFs
圍 Elem Tech Control S Real Constants 田 Material Props 田 Sections 田 Modeling 田 Meshing 田 Checking Ctrls 田 Numbering Ctrls 0 Archive Model E] Coupling / Ceqn S FLOTRAN Set Up 田 Multi-field Set Up S Loads
E) cs
田 Operations
0 Solution E) General Postproc
Defined Element Types:
NONE DEHNED
图1-1
/\ Library of Element T]
图1-2
2)在B单元类型的option选项中的K3下拉列表中选择3-D w/o rot iner。如图1-3所示。
图1-3
3)定义实常数。点击添加命令,在A单元的添加列表中添加数据,如图1 -4、1-5所示。
图1-5
定义材料性能参数
弹性模量EX=2ell,泊松比PRXY=O. 20如图1-6所示。
/\l_inear Isotropic Properties for Material Number 1
Linear Isotropic Material Properties for Material Number 1
T1
Temperatures
EX
PRXY
Material Models Available 总 Favorites 渗 Structural
渗 Linear
渗 Elastic
◎
Isotropic
◎ Orthotropic
图1-6
创建有限元模型
1)分别定义两个点(0, 0, 0)、(3, -4, 0) o如图1-7、1-8所示。
Create
田 Keypoints
田 Lines
田 Areas
El Volumes 曰 Nodes
刀 On Working Plane 園
刃 At Curvature Ctr 刃 On Keypoint 刃 Fill between Nds 闪 Quadratic Fill 田 Rotate Node CS 園 Write Node File
A Create Nodes in Active Coordinate Syste
[N] Create Nodes in Active Coordinate System NODE Node number
X,Y,Z Location in active CS
THXY,THYZ,THZX
Rotation angles (degrees)
1
匸
1° 11°
II l「
Cancel I Help
图1-7
A Create Nodes in Active Coordinate SystemJ I [N] Create Nodes in Active Coordinate System
NO